EVO MFG 3.5" JL High Clearance Long Arm Suspension System

EVO MFG 3.5" JL High Clearance Long Arm Suspension System

Your Price: $3,424.98
Retail Price:$3,767.48
Your Savings:$342.50(9%)
Typically Ships in 5-7 Business Days
Free Shipping
Part Number:EVO-3016

EVO MFG 3.5" JL High Clearance Long Arm Suspension System
 

The EVO MFG 3.5” JLU High Clearance Long Arm kit will like your JLU
3.5”s.   Through specifically designed bracketry we accomplish the
ultimate in suspension and chassis clearance, larger wheel travel
ability, optimal suspension geometry with increased ride quality. 
Clearance, ride quality, performance and ease of installation was
our focus in creating this long arm suspension system.  The front arms
mount tucked up inside nearly flush with the bottom of the frame
mounting inches above the stock front lower mounting bracket.  The rear
mounting locations for the long arm are on the side of the frame, above
the bottom giving inches of clearance over the factory locations as
well.  Keeping optimal geometry while maintaining as much clearance
was critical in the design of this system.  In doing so, not only did
we raise the rear control above the frame but we raised its mounting at
the rear axle by multiple inches as well.  This allows for an
incredible ground clearance increase but just as importantly retaining
flat and optimal control arm angles giving ideal ground clearance,
smooth ride quality and long travel ability. The mounting brackets are
specifically designed to require no exhaust cutting on 3.6L Jeep
Wrangler JLU’s (minor grind/clearance to flange required) and have full
length hard-face mounting surfaces that weld to your frame giving
redundant and ample welding area and strength to their mounting.  The
mounting brackets align to the frame simply using existing factory holes
giving complete assurance of proper locating during install.  Simply
bolt brackets up to frame with existing hardware and weld them in place.
These kits come with a set of 3.5” Plush Ride Lift springs specific to
each corner which will keep the Jeep Wrangler JLU more level side to
side and will maintain a unique and compliant ride quality. EVO MFG Long
Arm joints feature Johnny Joints on both ends of the control arms for
restriction free articulation and motion with no wearable and limited
bond rubber.  All long arms come complete with EVO1 on vehicle adjuster
making alignment a snap allowing for the ability to adjust control arm
lengths while completely installed on the vehicle at all times.  All EVO
MFG lower long arms are built with strength in mind.  These arms are
made from industry leading 2.0” x .281” wall Steel DOM Tubing. Include
in these kits is front brakeline extension brackets, Rear swaybar
endlinks and front and bumpstop extensions.  Cutting, grinding and
welding of frame brackets required.  The EVO MFG 3.5” High Clearance
Long Arm kits require no driveshaft or exhaust modifications (your shock
choice may require this, contact manufacturer to be sure).  Option of
retaining factory shocks, maintaining wheel travel with use of shock
extensions (part number EXT kits) or without shock extensions to allow
for use of your choice of aftermarket 3/5” lift shocks.  EVO3015K kits
come with EVO SPEC King 2.5” Remote Reservoir shocks all 4 corners. 
3.5” lift is based on increase of our 4 Door Rubicon.  4 Door Sport and
Sahara Models will see slightly higher increases over stock and will
match overall lift height of a Rubicon Model.  2 Door Models (all) will
see slightly higher increases in lift.  Increases will vary. 
Note:  Depending on actual tire variances and sizes, Some minor
factory inner liner plastic may need to trimmed/removed to fully clear
some tires under compression.  These kits require wheel spacers or
aftermarket wheels with smaller backspacing.  Adjustable Front Trackbar
is required to complete proper installation, not included.

Related Items